Individual differences |
Methods | Statistics | Clinical | Educational | Industrial | Professional items | World psychology |
A tuning fork is a piece of apparatus, an acoustic resonator in the form of a two-pronged fork with the prongs (tines) formed from a U-shaped bar of elastic metal (usually steel). It resonates at a specific constant pitch when set vibrating by striking it against a surface or with an object, and emits a pure musical tone after waiting a moment to allow some high overtones to die out. The pitch that a particular tuning fork generates depends on the length of the two prongs. Its main use is as a standard of pitch to tune other musical instruments.
Description[edit | edit source]
The main reason for using the fork shape is that, unlike many other types of resonators, it produces a very pure tone, with most of the vibrational energy at the fundamental frequency, and little at the overtones (harmonics). The reason for this is that the frequency of the first overtone is about 52/22 = 25/4 = 6¼ times the fundamental (about 2½ octaves above it). By comparison, the first overtone of a vibrating string or metal bar is only one octave above the fundamental. So when the fork is struck, little of the energy goes into the overtone modes; they also die out correspondingly faster, leaving the fundamental. It is easier to tune other instruments with this pure tone.
Another reason for using the fork shape is that, when it vibrates in its principal mode, the handle vibrates up and down as the prongs move apart and together. There is a node (point of no vibration) at the base of each prong. The handle motion is small, allowing the fork to be held by the handle without damping the vibration, but it allows the handle to transmit the vibration to a resonator (like the hollow rectangular box often used), which amplifies the sound of the fork. Without the resonator (which may be as simple as a table top to which the handle is pressed), the sound is very faint. The reason for this is that the sound waves produced by each fork prong are 180° out of phase with the other, so at a distance from the fork they interfere and largely cancel each other out. If a sound absorbing sheet is slid in between the prongs of a vibrating fork, reducing the waves reaching the ear from one prong, the volume heard will actually increase, due to a reduction of this cancellation.
Although commercial tuning forks are normally tuned to the correct pitch at the factory, they can be retuned by filing material off the prongs. Filing the ends of the prongs raises the pitch, while filing the inside of the base of the prongs lowers it.
Currently, the most common tuning fork sounds the note of A = 440 Hz, because this is the standard concert pitch, which is used as tuning note by some orchestras, it being the pitch of the violin's second string, the first string of the viola, and an octave above the first string of the cello, all played open. Tuning forks used by orchestras between 1750 and 1820 mostly had a frequency of A = 423.5 Hz, although there were many forks and many slightly different pitches. Standard tuning forks are available that vibrate at all the musical pitches within the central octave of the piano, and other pitches. Well-known manufacturers of tuning forks include Ragg and John Walker, both of Sheffield, England.
The pitch of a tuning fork can vary slightly with weathering and temperature. A decrease in frequency of one vibration in 21,000 for each °F change is typical for a steel tuning fork. The standard temperature is now 68 °F (20 °C) but 59 °F (15 °C) is an older standard. The pitches of a musical instrument such as an organ are also subject to variation with temperature change.
Calculation of frequency[edit | edit source]
The frequency of a tuning fork depends on its dimensions and the material from which it is made:
- f is the frequency the fork vibrates at in Hertz.
- 1.875 the smallest positive solution of cos(x)cosh(x) = -1.
- l is the length of the prongs in metres.
- E is the Young's modulus of the material the fork is made from in pascals.
- I is the second moment of area of the cross-section in metres to the fourth power.
- ρ is the density of the material the fork is made from in kilogrammes per cubic metre.
- A is the cross-sectional area of the prongs (tines) in square metres.
The ratio in the equation above can be rewritten as if the prongs are cylindrical of radius r, and if the prongs have rectangular cross-section of width a along the direction of motion.
Uses[edit | edit source]
Forks have traditionally been used to tune musical instruments, although electronic tuners are replacing them in many applications. Tuning forks can be driven electrically, by placing electromagnets close to the prongs that are attached to an electronic oscillator circuit, so that their sound does not die out.
In musical instruments[edit | edit source]
A number of keyboard musical instruments using constructions similar to tuning forks have been made, the most popular of them being the Rhodes piano, which has hammers hitting constructions working on the same principle as tuning forks and uses electric amplification of the generated sound. The earlier, unamplified dulcitone used tuning forks directly; it suffered from faintness of volume.
Medical and scientific uses[edit | edit source]
- Main article: Hearing test
An alternative to the usual A440 diatonic scale is that of philosophical or scientific pitch with standard pitch of C512. According to Rayleigh, the scale was used by physicists and acoustic instrument makers. The tuning fork that John Shore gave to Handel gives a pitch of C512.
Tuning forks, usually C512, are used by medical practitioners to assess a patient's hearing. Lower-pitched ones (usually C128) are also used to check vibration sense as part of the examination of the peripheral nervous system.
See also[edit | edit source]
References[edit | edit source]
- Reber, AS & Reber ES (2001). Dictionary of Psychology, 3rd ed. London:Penguin.
- (1997). History of the tuning fork. I: Invention of the tuning fork, its course in music and natural sciences. Pictures from the history of otorhinolaryngology, presented by instruments from the collection of the Ingolstadt German Medical History Museum. Laryngo- rhino- otologie 76 (2): 116–22.
- Tyndall, John (1915). Sound, New York: D. Appleton & Co..
- The Science of Sound, 3rd ed., Rossing, Moore, and Wheeler
- The Physics of Musical Instruments amazon.comTemplate:Page needed
- Journal of the Society of Arts, Vol. 28, p. 297
- (1999). Dynamics of Transversely Vibrating Beams Using Four Engineering Theories. Journal of Sound and Vibration 225 (5): 935.
- Whitney, Scott Vibrations of Cantilever Beams: Deflection, Frequency, and Research Uses. University of Nebraska–Lincoln. URL accessed on 2011-11-09.
- Rayleigh, J.W.S. (1945). The Theory of Sound, New York: Dover.
- The origin of the tuning fork - nih
[edit | edit source]
| Tuning forks]]
- Onlinetuningfork.com, an online tuning fork using Macromedia Flash Player.
- Usneurologicals.com, numerous examples of medical uses of tuning forks.