Individual differences |
Methods | Statistics | Clinical | Educational | Industrial | Professional items | World psychology |
Generally, an amplifier is any device that will use a small amount of energy to control a larger amount of energy. In popular use, the term today usually refers to an electronic amplifier, often as in audio applications. The relationship of the input to the output of an amplifier — usually expressed as a function of the input frequency — is called the transfer function of the amplifier, and the magnitude of the transfer function is termed the gain.
- 1 General characteristics of amplifiers
- 2 Electronic amplifiers
- 2.1 Electronic amplifier classes
- 2.2 Vacuum tube (valve) amplifiers
- 2.3 Transistor amplifiers
- 2.4 Operational amplifiers (op-amps)
- 2.5 Fully differential amplifiers (FDA)
- 2.6 Video amplifiers
- 2.7 Microwave amplifiers
- 3 Musical instrument (audio) amplifiers
- 4 Other amplifier types
- 5 References
- 6 See also
- 7 References
General characteristics of amplifiers[edit | edit source]
Most amplifiers can be characterized by a number of parameters.
Gain[edit | edit source]
Output dynamic range[edit | edit source]
Output dynamic range is the range, usually given in dB, between the smallest and largest useful output levels. Since the lowest useful level is limited by output noise, this is quoted as the amplifier dynamic range.
Bandwidth and rise time[edit | edit source]
The bandwidth (BW) of an amplifier is usually defined as the difference between the lower and upper half power points. This is therefore also known as the −3 dB BW. Bandwidths for other response tolerances are sometimes quoted (−1 dB, −6 dB etc.).
A full-range audio amplifier will be essentially flat between twenty hertz to about twenty kilohertz (the range of normal human hearing.) In minimalist amplifier design, the amp's usable frequency response needs to extend considerably beyond this (one or more octaves either side) and typically a good minimalist amplifier will have -3 dB points < 10 and > 65 kHz. Professional touring amplifiers often have input and/or output filtering to sharply limit frequency response beyond 20-20 kHz; too much of the amplifier's potential output power would otherwise be wasted on infrasonic and ultrasonic frequencies, and the danger of AM radio interference would increase. Modern switching amplifiers need steep low pass filtering at the output to get rid of high frequency switching noise and harmonics.
The rise time of an amplifier is the time taken for the output to change from 10% to 90% of its final level when driven by a step input.
Many amplifiers are ultimately slew rate limited (typically by the impedance of a drive current having to overcome capacitive effects at some point in the circuit), which may limit the full power bandwidth to frequencies well below the amplifiers frequency response when dealing with small signals.
For a Gaussian response system (or a simple RC roll off), the rise time is approximated by:
Settling time and aberrations[edit | edit source]
Time taken for output to settle to within a certain percentage of the final value (say 0.1%). This is usually specified for oscilloscope vertical amplifiers and high accuracy measurement systems.
Slew rate[edit | edit source]
Slew rate is the maximum rate of change of output variable, usually quoted in volts per second (or microsecond).
Noise[edit | edit source]
This is a measure of how much noise is introduced in the amplification process. Noise is an undesirable but inevitable product of the electronic devices and components. It is measured in either decibels or the peak output voltage produced by the amplifier when no signal is applied.
Efficiency[edit | edit source]
Efficiency is a measure of how much of the input power is usefully applied to the amplifier's output. Class A amplifiers are very inefficient, in the range of 10–20% with a max efficiency of 25%. Modern Class AB amps are commonly between 35–55% efficient with a theoretical maximum of 78.5%. Commercially available Class D switching amplifiers have reported efficiencies as high as 97%. The efficiency of the amplifier limits the amount of total power output that is usefully available. Note that more efficient amplifiers run much cooler, and often do not need any fans even in multi-kilowatt designs.
Linearity[edit | edit source]
An ideal amplifier would be a totally linear device, but real amplifiers are only linear within certain practical limits. When the signal drive to the amplifier is increased, the output also increases until a point is reached where some part of the amplifier becomes saturated and cannot produce any more output; this is called clipping, and results in distortion.
Some amplifiers are designed to handle this in a controlled way which causes a reduction in gain to take place instead of excessive distortion; the result is a compression effect, which (if the amplifier is an audio amplifier) will sound much less unpleasant to the ear. For these amplifiers, the 1dB compression point is defined as the input power (or output power) where the gain is 1dB less than the small signal gain.
Linearization is an emergent field, and there are many techniques, such us feedforward, predistortion, postdistortion, EER, LINC, CALLUM, cartesian feedback, etc., in order to avoid the undesired effects of the non-linearities.
Electronic amplifiers[edit | edit source]
- Main article: Electronic amplifier
There are many types of electronic amplifiers for different applications.
One common type of amplifier is the electronic amplifier, commonly used in radio and television transmitters and receivers, high-fidelity ("hi-fi") stereo equipment, microcomputers and other electronic digital equipment, and guitar and other instrument amplifiers. Its critical components are active devices, such as vacuum tubes or transistors.
Electronic amplifier classes[edit | edit source]
Amplifiers are commonly classified by the conduction angle (sometimes known as 'angle of flow') of the input signal through the amplifying device.
- Class A
- Where efficiency is not a consideration, most small signal linear amplifiers are designed as Class A, which means that the output devices are always in the conduction region. Class A amplifiers are typically more linear and less complex than other types, but are very inefficient. This type of amplifier is most commonly used in small-signal stages or for low-power applications (such as driving headphones).
- Class B
- In Class B, there are two output devices (or sets of output devices), each of which conducts alternately for exactly 180 deg (or half cycle) of the input signal.
- Class AB
- Class AB amplifiers are a compromise between Class A and B, which improves small signal output linearity; conduction angles vary from 180 degrees upwards, selected by the amplifier designer. Usually found in low frequency amplifiers (such as audio and hi-fi) owing to their relatively high efficiency, or other designs where both linearity and efficiency are important (cell phones, cell towers, TV transmitters).
- Class C
- Popular for high power RF amplifiers, Class C is defined by conduction for less than 180° of the input signal. Linearity is not good, but this is of no significance for single frequency power amplifiers. The signal is restored to near sinusoidal shape by a tuned circuit, and efficiency is much higher than A, AB, or B classes of amplification.
- Class D
- Main article: Switching amplifier
- These use switching to achieve a very high power efficiency (more than 90% in modern designs). By allowing each output device to be either fully on or off, losses are minimized. A simple approach such as pulse-width modulation is sometimes still used; however, high-performance switching amplifiers use digital techniques, such as sigma-delta modulation, to achieve superior performance. Formerly used only for subwoofers due to their limited bandwidth and relatively high distortion, the evolution of semiconductor devices has made possible the development of high fidelity, full audio range Class D amplifiers, with S/N and distortion levels similar to their linear counterparts.
- Other classes
- There are several other amplifier classes, although they are mainly variations of the previous classes. For example, Class H and Class G amplifiers are marked by variation of the supply rails (in discrete steps or in a continuous fashion, respectively) following the input signal. Wasted heat on the output devices can be reduced as excess voltage is kept to a minimum. The amplifier that is fed with these rails itself can be of any class. These kinds of amplifiers are more complex, and are mainly used for specialized applications, such as very high-power units. Also, Class E and Class F amplifiers are commonly described in literature for radio frequencies applications where efficiency of the traditional classes deviate substantially from their ideal values. These classes use harmonic tuning of their output networks to achieve higher efficiency and can be considered a subset of Class C due to their conduction angle characteristics.
- Power Amplifier
The term "power amplifier" is a relative term with respect to the amount of power delivered to the load and/or sourced by the supply circuit. In general a power amplifier is designated as the last amplifier in a transmission chain and is the amplifier stage that typically requires most attention to power efficiency. For these reasons, a power amplifier is typically any of the above-mentioned classes except Class A.
Vacuum tube (valve) amplifiers[edit | edit source]
- Main article: valve amplifier
According to Symons, while semiconductor amplifiers have largely displaced valve amplifiers for low power applications, valve amplifiers are much more cost effective in high power applications such as "radar, countermeasures equipment, or communications equipment" (p. 56). Many microwave amplifiers are specially designed valves, such as the klystron, gyrotron, traveling wave tube, and crossed-field amplifier, and these microwave valves provide much greater single-device power output at microwave frequencies than solid-state devices (p. 59).
Transistor amplifiers[edit | edit source]
- Main article: transistor
The essential role of this active element is to magnify an input signal to yield a significantly larger output signal. The amount of magnification (the "forward gain") is determined by the external circuit design as well as the active device.
Many common active devices in transistor amplifiers are bipolar junction transistors (BJTs) and metal oxide semiconductor field-effect transistors (MOSFETs).
Applications are numerous, some common examples are audio amplifiers in a home stereo or PA system, RF high power generation for semiconductor equipment, to RF and Microwave applications such as radio transmitters.
Transistor-based amplifier can be realized using various configurations: for example with a bipolar junction transistor we can realize common base, common collector or common emitter amplifier; using a MOSFET we can realize common gate, common source or common drain amplifier. Each configuration has different characteristic (gain, impedance...).
Operational amplifiers (op-amps)[edit | edit source]
- Main article: operational amplifier
An operational amplifier is a solid state integrated circuit amplifier which employs external feedback for control of its transfer function or gain.
Fully differential amplifiers (FDA)[edit | edit source]
- Main article: fully differential amplifier
A fully differential amplifier is a solid state integrated circuit amplifier which employs external feedback for control of its transfer function or gain. It is similar to the operational amplifier but it also has differential output pins.
Video amplifiers[edit | edit source]
These deal with video signals and have bandwidths of about 5 MHz. Certain requirements for step response and overshoot are necessary in order for acceptable TV images to be presented.
Oscilloscope vertical amplifiers[edit | edit source]
These are used to deal with video signals to drive an oscilloscope display tube and can have bandwidths of about 500 MHz. The specifications on step response, rise time, overshoot and aberrations can make the design of these amplifiers extremely difficult. One of the pioneers in high bandwidth vertical amplifiers was the Tektronix company.
Distributed amplifiers[edit | edit source]
- Main article: Distributed Amplifier
These use transmission lines to temporally split the signal and amplify each portion separately in order to achieve higher bandwidth than can be obtained from a single amplifying device. The outputs of each stage are combined in the output transmission line. This type of amplifier was commonly used on oscilloscopes as the final vertical amplifier. The transmission lines were often housed inside the display tube glass envelope.
Microwave amplifiers[edit | edit source]
Travelling wave tube (TWT) amplifiers[edit | edit source]
- Main article: Traveling wave tube
Used for high power amplification at low microwave frequencies. They typically can amplify across a broad spectrum of frequencies; however, they are usually not as tunable as klystrons.
Klystrons[edit | edit source]
- Main article: Klystron
Very similar to TWT amplifiers, but more powerful and with a specific frequency "sweet spot". They generally are also much heavier than TWT amplifiers, and are therefore ill-suited for light-weight mobile applications. Klystrons are tunable, offering selective output within their specified frequency range.
Musical instrument (audio) amplifiers[edit | edit source]
- Main article: instrument amplifier
An audio amplifier is usually used to amplify signals such as music or speech.
Other amplifier types[edit | edit source]
Carbon microphone[edit | edit source]
One of the first devices used to amplify signals was the carbon microphone (effectively a sound-controlled variable resistor). By channeling a large electric current through the compressed carbon granules in the microphone, a small sound signal could produce a much larger electric signal. The carbon microphone was extremely important in early telecommunications; analog telephones in fact work without the use of any other amplifier. Before the invention of electronic amplifiers, mechanically coupled carbon microphones were also used as amplifiers in telephone repeaters for long distance service.
Magnetic amplifier[edit | edit source]
- Main article: magnetic amplifier
A magnetic amplifier is a transformer-like device that makes use of the saturation of magnetic materials to produce amplification. It is a non-electronic electrical amplifier with no moving parts. The bandwidth of magnetic amplifiers extends to the hundreds of kilohertz.
Optical amplifiers[edit | edit source]
- Main article: Optical amplifier
Miscellaneous types[edit | edit source]
- There are also mechanical amplifiers, such as the automotive servo used in braking.
- Relays can be included under the above definition of amplifiers, although their transfer function is not linear (that is, they are either open or closed).
- Also purely mechanical manifestations of such digital amplifiers can be built (for theoretical, didactical purposes, or for entertainment), see e.g. domino computer.
- Another type of amplifier is the fluidic amplifier, based on the fluidic triode.
References[edit | edit source]
- Robert S. Symons (1998). Tubes: Still vital after all these years. IEEE Spectrum 35 (4): 52–63.
See also[edit | edit source]
References[edit | edit source]
|This page uses Creative Commons Licensed content from Wikipedia (view authors).|